Видео

Good thing I'm paid by the hour. These things suck. But I guess when you stroke out a 454 and put a blower on it, you might as well take your time now not later.

They went from putting valve covers on to dyno test with twin turbos.

worst idea ever implemented into these motors

What gas do you have to use? Can you stick with Reg, or need to use Premium.

But how much flow does your engine produce in a single pipe? For instance, a Suburban can hold more than a Civic, but if it's just you and your wife, the extra space is wasted.

Merci beaucoup ❤❤❤❤❤❤❤

So synthetic oil doesn’t cause leaks but it does cause leaks 🤣 you might see drips on the driveway but they aren’t really there

How is the power valve going to effect idle quality?

Jeez its so effing clean underneath.

Yes, but how many cfm depends on engine exhaust air flow. Maybe you only need 300 cfm. It would be interested to see pressure results. Either way, Magnaflows don't usually sound good by themselves.

Now do the same thing with bigger turbos or switch to a turbo with larger hot side.. That glowing red is from too much back pressure.

Tips cost y much.

Where can I find the chart explaining the “series style ignition systems” as your video explains using one wire specification up to the “six series style ignition” and I would like to know the series style of my ignition system?

Have you ever installed a 200 amp one wire Powermaster Alt on a Vortech supercharged 302 block Mustang? Alternator is on passenger bottom location.

Hot water

Warped Heads Baby!

These containers are unnecessary planet busting garbage.

Put a drop of motor oil instead. Its free and does the same thing.

BEAST

Maybe if you are dealing with chevrolet but not with a ford engine. Pistons i have in my 307 cid build has no spec on valve relief angle but it does have a spec of working with 1.98"/1.64" valves which my Renegade 165cc heads use a 1.90"/1.60" valve. I didnt waste time with checking piston to valve clearance as there is no physical way for the valve to evenbtouch the piston even with a 0.0015" deck clearance, running 0.040" quench and the fact the valves are recessed in a heart chamber in the head even at 0.520"/0.542" lift it wont touxh unless a valve is dropped. On GM how ever sure check it wince they have all weird kind of twists and angle changes made

Coca-Cola followed by water followed by no locks, you're welcome

Can’t look past the front bumper fitment of that nova looks like the bumper is leaning back 😂

can't you just use baking soda

for it being a "middle of the road" bumper i'd expect it to be cheaper than a full on welded iron bumper with a grille guard like a "Ranch Hand" bumper. This thing goes for $2700+shipping/tax from what I have seen. A Ranch Hand bumper will run you like $1800+shipping/tax and will last much longer. Listen, I'm all for the style of AEV but why so expensive? You can literally get a better performing bumper (improved approach angle and ground clearance) that is hand made in the US from chassis unlimited for the same price or less (depending on which bumper you choose). idk man, to me AEV is not it.

My car has a very thin flexplate which keeps breaking and i dont know what to do.can i upgradeit a durable one?the car make is mitsubishi colt 2003.you can send me your email so that we can share more about this car and maybe i can get help

How about show what your actually doing not just a video of you doing it from far away

I always use gauge blocks and the Fowler fixture to set the dial bore gauge.

I'm investigating this for a 6.7 Powerstroke as a way to combat gumming up due to EGR.

Would the 4032 be good in a daily driver truck application? I had planned to go with Hypereutectic pistons for my LQ4 thats getting a 4 inch stroke but I haven't found any hypereutectic pistons for a stroker motor

Why fill half way on the oil filter?

Awesome set of parts

does the front bumper fits the 1500 Ram models?

How many amps would that fan draw?

All the comments here are correct: this myth needs to die. This entire video is bs. Not only does dish soap not contain abrasives, it doesn't harm clear coat, and it won't even remove wax until after a dozen washes with it. Just utter complete bs. Dish soap is fine. I think the industry is jealous that there is such an inexpensive incumbent readily available.

Oh, yeah

Its a 3100 not an apache. 1958/59 are apache years

What a wonderful truck! It is a shame you don’t love it and will not fix the terrible rust. No, it’s NOT cool.

Understanding the mentality of management is vital to making smart investment decisions, so glad I sold my stock. Thanks.

Thinking of adding water or water/methanol injection to my TDI. Gotta check with Gale first.

I need this tool!

WELCOME BACK TO 1984!!!!

PRINTED SOCIAL MEDIA IS HOT IN 1984!!!!!

I THANK YOU AND I LOVE YOU!!!!

THANK YOU TO ALL THE BRANDS IN THIS BUILD.

DAILY DRIVERS ARE HOT!!!!!

A TOTALLY AWSOME VIDEO AND A TOTALLY AWSOME BUILD!!!! THANKS FOR SHARING!!!! I LEARNED ALOT!!!

THANK YOU SO MUCH!!!!

TOTALLY AWSOME VIDEO JUSTIN!!!!!

THANK YOU SO MUCH!!!! PERFECT FOR MY DAILY DRIVER!!!!

"Patina" is an ancient word for "To lazy to fix it properly".